HPD385 open Sheng both week 後, having with 50 veneered end 擴 big airport repair good, and TV source and the Horn online roughly finishing dry net, Sheng sound are once than once progress step, Zhang paper 俠 Mr 贊 help of Horn box results institution phase when 堅 solid, no what so question problem, not over this Horn box still has two real question problem phase when trapped 擾 I:

Maximum of question problem is it of stadium equivalent of, by in when early design total is put in walls angle, so Horn box is class like isosceles right triangle design total, put in walls angle when veneered Stadium 剛 good is 45 degrees Yes hearing Ting location, question problem is this model courses 擺 low frequency too more not said, by in Horn points to fixed, completely cannot method Zambia whole sound Gatwick, so real to using of said still is have drag out walls angle, Horn oriented Bai are, only slightly toe-in a little, this model courses of said a support Horn surface 寬 90 cm. Two are 180 cm, I only have four rooms 寬 meters, intermediate one projection screen 寬 240 cm, loudspeaker able find location around is very limited. Second real question problem is to how Shang foot frame, Horn box high although 110 cm, not over put Shang veneered Stadium 後, veneered Stadium Center from-Zaventem ground big approximately 85 cm around, slightly low has little, need put Horn frame high approximately 10 cm, heel ever reinforced of is this isosceles triangle of bottom, plus still has a circle skirt foot, this how design total foot frame does?

About in first real question problem, I wants to 暫 when is cannot solutions has, may to more 嘗 General different of Qian 後 擺 bit stub toe-in, to in second real question problem, too complexity 雜 of foot frame Ying this is cannot method do has, and even do has put up also bad see, I wants to has wants to, best of way Ying this is using it originally include sliding round of hole bit, views Shang screw hex directly down, this model courses a future, not only modified begins to small, using screw hex screw Wen still can micro-Zambia Horn height, 穩 qualitative Ying this also not wrong.

Conditions thought for a moment, Ying this didn't have any big problem problem, 驅 car to the hex shop posted by bought materials. Had hoped more than enough with 15mm hex, 詢 problem used to four-foot Ding the maximum fruit only three points, no 訂, minimum order to 1k above, had to choose liquid three-hex. Bought hex specification for the first time is three-inch-long steel hex socket cap screws hex hex, nut, Dan Secretary stub full gasket spring in South China. After home, while his wife and children were away, keep the Horn tank, bottom of the four-foot Ding'll promote knocks progress. Although wooden materials is higher density than MDF, HDF, just the phase when the software, used large iron hammer is easy to progress. Next turn the speakers are in the future, 'll hex to promote bass reflex port into the box inside, include the four-foot eye, each hex are all sets of nuts, as well as full gasket above, when the height adjust nut after good, it'll include hex could be the nut down tightly to avoid sell slide begins to screw in the four-foot Ding.

Installation on foot after Ding, voice was much clearer, less low frequency comparison, this is sure then, boxes on the gun LUN, 搖 搖 was perched precariously low frequency impossible. Not only three inches over the hex, pull off the nut and the plate thickness, meat Xian ' highly limited, had to hex again store bought a long hex for the second time. Screw hex line told I to of long degrees, no has whole only screw teeth of, this early in I expected in the, modified because b total 畫, bought has two support a meters long of not stainless steel teeth terms, home with sand round airport Saw air circuit breakers, put end bottom mill round when for foot Ding, addition end with two real nut mutual include, teeth terms on change into has a support is long of outside six angle screw hex, sets Shang Chinese Division and fuel ectonomc tablets, this times 輕 輕 convenient convenient to on put Horn increased ten cm around.

Because hex Super wear-resistant floor scraper Huai 貴 a killer Quickstep, I went to B&Q Saw two 塊-100cmx90cm two Jia, fuel ectonomc on the ground when the o. Due to be hex is hand ground, not round at the bottom, only include hex then wants to move begins on trumpets release Jia panels've hex on MO Qian Qian hole, for a Secretary do predict control measures. Hex is due to three points, and 蠻 long, plus a fixed weighting bian edge at the bottom still is a not small-Zaventem, Feeling not quite so box 穩-solid, maybe gap than I expected just the s to free again to other Office law.

Remove comes for the first time include three-point hex

Trumpet after high fuel ectonomc model courses